//初始化文件格式说明
//	每一行表示一条命令
//	每一行的第一个值为命令，第二个值为长度，后面跟上对应长度的值，如果长度为0，不需要再跟上值
//              如果一行已//开始，表示注释
//              禁止在命令行内添加注释
//延时设置：特殊情况，两个0xfe, 0xfe 表示延迟,
//	例如  0xfe, 0xfe, 120, 表示延迟120毫秒 
//通讯方式：3线9bit	u8cmd, u8size, u8val,
//	例如  0xC1,1, 0x3F, 表示寄存器0xC1， 1个值，0x3f值
//通讯方式：3线16bit	u16cmd, u16size, u16val,
//	例如  0xC301, 0x01, 0x22, 表示寄存器0xC301， 1个值，0x22值
//	例如  0x1101, 0x00, 表示寄存器0x1101， 0个值，无值
//注意1：SPI初始化必须配置通讯IO：SPI_CS、SPI_SDA、SPI_SCK
//注意2：LCD_RST可选配置，根据硬件设置，如RC复位则不需要配置rst，0xFF表示不存在PIN
//注意3：当无数据的参数，为了方便统一为1个数据，不会影响整个初始化
//	例如  cmd：0x29, 表示亮屏命令0x29，
//  更改  0x29,1, 0x00,
//注意4：MIPI参数初始化参考3B9模式

0xF0,5, 0x55,0xaa,0x52,0x08,0x00,
0xF6,2, 0x5a,0x87,
0xC1,1, 0x3F,
0xCD,1, 0x25,
0xC9,1, 0x10,
0xF8,1, 0x8A,
0xAC,1, 0x65,
0xA7,1, 0x47,
0xA0,1, 0x99,
0x86,4, 0x99,0xA3,0xA3,0x41,
0x87,3, 0x04,0x03,0x66,
0xFA,4, 0x08,0x08,0x00,0x04,
0xA3,1, 0x6E,
0xFD,3, 0x28,0x3C,0x00,
0x9A,1, 0x6d,
0x9B,1, 0x44,
0x82,2, 0x22,0x22,
0xB1,1, 0x10,
0x7A,2, 0x0F,0x13,
0x7B,2, 0x0F,0x13,
0x69,7, 0x14,0x22,0x14,0x22,0x44,0x22,0x08,
0x6B,1, 0x07,
0x60,8, 0x38,0x0C,0x12,0x64,0x38,0x0B,0x12,0x64,
0x61,8, 0x33,0xC2,0x6A,0x39,0xB3,0xC9,0x52,0x52,
0x62,8, 0xB3,0xC9,0x52,0x52,0x33,0xC2,0x6A,0x39,
0x63,8, 0x38,0x0A,0x12,0x64,0x38,0x09,0x12,0x64,
0x64,16, 0x38,0x08,0x03,0xC0,0x03,0x03,0x38,0x06,0x03,0xc2,0x03,0x03,0x12,0x64,0x12,0x64,
0x65,16, 0x38,0x04,0x03,0xc4,0x03,0x03,0x38,0x02,0x03,0xc6,0x03,0x03,0x12,0x64,0x12,0x64,
0x66,16, 0x83,0xD5,0x03,0xC9,0x03,0x03,0x83,0xD5,0x03,0xc9,0x03,0x03,0x52,0x52,0x52,0x52,
0x11,1, 0x00, 
0xfe, 0xfe, 120,
0x29,1, 0x00,